Wagner-spraytech CS9100 Bedienungsanleitung

Diaphragm Pumps1150Piston PumpsEP2105EP2205EP2300EP2300seEP2400EP2510GP2605GP2905HVLPCS5100CS8100CS9100Maxum II GunDiaphragm Pumps1150Piston PumpsEP21

8The paint pump is located below the hydraulic pump (seeFigure 1). The two pumps are bolted together by foursocket head capscrews. The diaphragm separ

9tainer. When the priming knob is turned to (prime), paintis drawn up the suction tube into the paint pump. The paintpump then routes the paint t

10ASSEMBLY OF A NEWSPRAYER1. Screw the return fitting into the elbow on the front sideof the paint pump. Both fittings should be hand tight only,but t

114. Tighten tip nut. The tip guard should now be in the properposition. See Figure 5.Figure 4.- Spray Gun Tip Guard Postion BeforeTightening.3. Lo

12OPERATIONSTART UP PROCEDURESPRAY PAINTINGYou can learn to spray paint as easy as you can learn topaint with a brush or roller. You can get a profess

132. Avoid sharp bending and kinking of the paint hose. Thepaint hose and electric cord should be kept clear of trafficand sharp cutting edges or obje

14SPRAY TIP PLUGGINGThe spray tip can be plugged by foreign matter and “skin”in the paint. Excessively large paint pigments can also plugthe tip. If t

15IMPORTANT!Tighten the (4) Pump Block Bolts after the first 20 hoursof use.To tighten, use the 6mm allen wrench supplied in theliterature kit. Use a

16CHECKING OPERATION OF INLET VALVESee Figure 14 for location of inlet valve. The inlet valveshould be checked if the sprayer draws up little or no

17When the diaphragm or diaphragm parts have to be re-placed, proceed as follows:1. Remove the 4 paint pump screws with a 6 millimeteralIen wrench. As

18ProblomSprayer does not startupSprayer starts up butdoes not draw up paintSprayer draws up paintbut pressure does notbuild upCauseTROUBLESHOOTINGPro

19TROUBLESHOOTING (Continued)ProblemSprayer draws up paint,pressure builds up, butdrops away markedlywhen gun is opened (lowperformance) Pressure

20TROUBLESHOOTlNG (Concluded)1. Worn valve ball holder ongun1. Out of spray material2. Spray tip or gun filterplugged1. Partially plugged spray tip or

21ITEM PART NO. DESCRIPTION QTY.ITEM PART NO. DESCRIPTION QTY.1 0288478 Grip, 12 0294511 Handle 13 0088328 Washer, Lock, 5/16" 44 9800325 Screw,

22Paint Pump Assembly — Figure 19©1995 WAGNER SPRAY TECH CORPORATION. ALL RIGHTS RESERVED.‰123456789101112131417181719202122232425261516

23 PAINT PUMP ASSEMBLY — Figure 19ITEM PART NO. DESCRIPTION QTY.ITEM PART NO. DESCRIPTION QTY.1 0270201 Diaphragm assy. 12 0270494 Ring, diaphragm 13

240294218 SUCTION SET ASSEMBLYITEM PART NO. DESCRIPTION QTY.ACCESSORIESPart No. Description0153--- Tungsten C arbide Flat Tips0153003 Tip Guard, Flat

28What Is Covered By This Warranty:This product, manufactured by SprayTech Corporation (SprayTech), is warranted against defects in material and work

1Owner's ManualED1150 Airless SprayerModel no. 0294059Form no. 0294968C© 1996 Wagner Spray Tech. All rights reserved.Plus

2THIS UNIT IS PROVIDED WITH A THERMALLY PROTECTED AUTOMATIC RESET. IF AN OVERLOADOCCURS THE THERMALLY PROTECTED AUTOMATIC RESET DISCONNECTS THE MOTOR

3SAFETY PRECAUTIONSThis manual contains information which must be read and understood before using the equipment. When you come to anarea which has on

4WARNINGPREVENTIONHAZARD • • Paint hose can develop leaks from wear, kinking, abuse,etc. A leak is capable of injecting material into the skin.The pai

5WARNINGHAZARD PREVENTIONExplosion or fire - Solvent and paint fumes can explode orignite causing property damage and/or severe injury.• Exhaust and f

6WARNINGPREVENTIONHAZARDExplosion hazard incompatible materials - May causeproperty damage or severe injury.General - May cause property damage or s

7GENERAL DESCRIPTIONBe sure to read the IMPORTANT SAFETY INFORMA-TION on pages 3 thru 6 before using this sprayer.Your SprayTECH sprayer is a powerful